TETENAL COLOTEC E-6
KIEV-60 TTL 80mm/f2.8/FUJI Velvia RVP100 /TETENAL COLOTEC E-6/GT-X800 
KIEV-60 TTL 80mm/f2.8/FUJI Velvia RVP100 /TETENAL COLOTEC E-6/GT-X800
Private development of a reversal film. ( TETENAL) First of all, it is the first developing solution of preparation of liquid. The concentration liquid of Erstentwickler is thinned with water of 20 to 40 degrees, and the whole quantity is made into 1l. (I did not use refining water.) I am untidy. I was simple using the mixed cock of water service in temperature management. It is drink tap water and is about 30 degrees. Coloring developing solution. The Farbentwickler part 1 and the part 2 were mixed with the drink tap water of 30 degrees, and it considered as 1l. of whole quantity. Just as they mixed, they were colored purple-blue. I considered, shortly after failing. Tap water worried about me with whether it is the cause. However, it was not a big mistake. When it became a purple-blue color in the appending document immediately after mixed churning and changed to yellow brown gradually, there was a publication. Bleaching fixing solution. The Bleichfixerbad part 1 and the part 2 were thinned with the tap water of 30 degrees, and the whole quantity was made into 1l. Stable liquid. Cautions were written that the temperature with a temperature higher than 25 degrees is bad to the appending document. I thinned it with the drink tap water of 23 degrees, and was taken as 1l. of whole quantity. This time, I challenge by the plastic tank which can measure an inner temperature also during churning.
KIEV-60 TTL 80mm/f2.8/FUJI Velvia RVP100 /TETENAL COLOTEC E-6/GT-X800
KIEV-60 TTL 80mm/f2.8/FUJI Velvia RVP100 /TETENAL COLOTEC E-6/GT-X800
For liquid temperature, the first development is 38 degrees. Coloring development is 38 degrees. Bleaching fixing is 36 degrees. Stable processing is 25 degrees from 20 degrees. In order to make it such temperature, I collected water of 40 degrees in the washstand of a house, and adjusted briskly. About the flush after each liquid processing I adjusted the temperature of the mixed cork of the hot water of a house, and tap water at 38 degrees from 37 degrees, poured into the tank, and washed the film. Flush time is indicated to be 2 minutes and 30 seconds by the appending document. However, I have taken time in a temperature setup of a bleaching fixing solution at the time of the flush after coloring development. I exceeded time from 3 by the reason for 4 minutes. results are the photographs carried here By these, I got satisfaction mostly. I worked between all distance, having carried out the latex glove. This is required in order to protect your skin and health.
Other photos are here.
KIEV-60 TTL 80mm/f2.8/FUJI Velvia RVP100 /TETENAL COLOTEC E-6/GT-X800
Private development of a reversal film. ( TETENAL) First of all, it is the first developing solution of preparation of liquid. The concentration liquid of Erstentwickler is thinned with water of 20 to 40 degrees, and the whole quantity is made into 1l. (I did not use refining water.) I am untidy. I was simple using the mixed cock of water service in temperature management. It is drink tap water and is about 30 degrees. Coloring developing solution. The Farbentwickler part 1 and the part 2 were mixed with the drink tap water of 30 degrees, and it considered as 1l. of whole quantity. Just as they mixed, they were colored purple-blue. I considered, shortly after failing. Tap water worried about me with whether it is the cause. However, it was not a big mistake. When it became a purple-blue color in the appending document immediately after mixed churning and changed to yellow brown gradually, there was a publication. Bleaching fixing solution. The Bleichfixerbad part 1 and the part 2 were thinned with the tap water of 30 degrees, and the whole quantity was made into 1l. Stable liquid. Cautions were written that the temperature with a temperature higher than 25 degrees is bad to the appending document. I thinned it with the drink tap water of 23 degrees, and was taken as 1l. of whole quantity. This time, I challenge by the plastic tank which can measure an inner temperature also during churning.
KIEV-60 TTL 80mm/f2.8/FUJI Velvia RVP100 /TETENAL COLOTEC E-6/GT-X800
KIEV-60 TTL 80mm/f2.8/FUJI Velvia RVP100 /TETENAL COLOTEC E-6/GT-X800
For liquid temperature, the first development is 38 degrees. Coloring development is 38 degrees. Bleaching fixing is 36 degrees. Stable processing is 25 degrees from 20 degrees. In order to make it such temperature, I collected water of 40 degrees in the washstand of a house, and adjusted briskly. About the flush after each liquid processing I adjusted the temperature of the mixed cork of the hot water of a house, and tap water at 38 degrees from 37 degrees, poured into the tank, and washed the film. Flush time is indicated to be 2 minutes and 30 seconds by the appending document. However, I have taken time in a temperature setup of a bleaching fixing solution at the time of the flush after coloring development. I exceeded time from 3 by the reason for 4 minutes. results are the photographs carried here By these, I got satisfaction mostly. I worked between all distance, having carried out the latex glove. This is required in order to protect your skin and health.
Other photos are here.
posted by hira16s at 6:43 PM
0 comments
